Insulation Calculator

Insulating walls or an attic? Enter the size and the coverage on the bag, and we work out the square feet and bags of batts to buy.

Updated Nov 2026 Formula shown below Feet or meters
ft
add up every wallEnter a number (0 or more)
ft
floor to ceilingEnter a number (0 or more)
ft
Enter a number (0 or more)
ft
Enter a number (0 or more)
Framing spacing on center
10%
7%
sq ft
check the labelEnter a number (0 or more)
sq ft
check the labelEnter a number (0 or more)
%
5–10% is typicalEnter a number (0 or more)
Your prices (optional)
$each
Enter a number (0 or more)
You'll need
–
stay cozy out there ✌

How to calculate insulation

Batt insulation is sold by the area it covers. Work out the area you're insulating, take off the part filled by studs or joists, add a little for waste, and divide by the coverage printed on the bag.

Bags = Area × (1 − Framing %) × (1 + Waste %) ÷ Area per bag

For walls, the area is the total length of the walls times their height. Subtract big openings, like a garage door or a patio slider, from the length. For an attic, the area is the length times the width of the space you're covering. Studs fill roughly 10% of a wall. Attic joists take a little less, about 5–10%, depending on their spacing. Doing walls and an attic? Run the calculator once for each and add the bags together.

Pro tip!

Read the bag before you trust any estimate. Coverage varies a lot between brands, thicknesses and batt widths, so type in the number printed on the package you plan to buy.

Worked example: 96 ft of 8 ft walls

Say you're insulating the outside walls of a 24 × 24 ft room: 96 feet of wall, 8 feet tall, with studs 16 inches on center. You're using R-13 batts, and each bag covers 100 sq ft.

  1. Find the wall area96 × 8 = 768 sq ft
  2. Take off 10% for studs768 × 0.90 = 691.2 sq ft
  3. Add 5% for waste691.2 × 1.05 = 725.8 sq ft
  4. Divide by bag coverage725.8 ÷ 100 = 7.3 → 8 bags

Common batt R-values and thickness

R-value measures how well insulation resists heat flow. Higher is better, but thicker batts need deeper framing to fit without being squashed.

R-valueTypical thicknessCommon use
R-133.5 in2×4 walls
R-153.5 in2×4 walls (denser batt)
R-196.25 in2×6 walls, floors
R-215.5 in2×6 walls (denser batt)
R-30About 9.5–10 inAttics, ceilings
R-38About 12 inAttics, ceilings
R-49About 15 inAttics, often an R-30 layer plus an R-19 layer

Thickness varies by product. Recommended R-values depend on your climate zone and local code, so check with your local building department before you buy.

Batt width and framing spacing

Batts are made to fit between standard framing. Batts about 15 inches wide fit studs or joists 16 inches on center, and batts about 23 inches wide fit framing 24 inches on center. Cut batts around wires and pipes rather than stuffing them behind. In the attic, a second layer laid across the joists covers the wood too, so you can set the framing factor to 0% for that layer.

Questions people ask

What R-value insulation do I need?

It depends on your climate zone, the part of the house and your local code. For an uninsulated attic, ENERGY STAR recommends R-30 to R-49 in the warmest zone and R-49 to R-60 in most of the US. Walls are usually R-13 to R-21. Check with your local building department too.

How many square feet does a bag of insulation cover?

It varies a lot. Thin wall batts often cover far more per bag than thick attic batts, and widths differ too. Always use the coverage printed on the package.

Do I subtract the studs when measuring?

Yes. Studs take up roughly 10% of a typical wall, and attic joists a bit less. The framing factor in the calculator handles this for you.

Should I use faced or unfaced batts?

Kraft-faced batts have a paper facing that acts as a vapor retarder and makes stapling easier. Unfaced batts are used where no retarder is wanted, like a second attic layer. Local code and climate decide which you need.

Sources

The numbers in this calculator come from these manufacturer specs and public guides. Always check the label on the product you buy.

  1. Recommended R-values by climate zone for attics and walls — ENERGY STAR
  2. Batt R-values, thicknesses and 15/23 in widths — Owens Corning PINK Next Gen data sheet
Was this calculator helpful?

Finishing the walls next?

See all calculators