How to calculate roofing shingles
You don't need to climb on the roof to estimate it. Measure the house footprint, add the overhang on every side, then multiply by a pitch multiplier to account for the slope. Divide by 100 to get roofing squares, add waste, and multiply by the bundles per square.
The pitch multiplier is √(1 + (rise ÷ 12)²). A steeper roof has more surface than its footprint, so the multiplier grows with the pitch. The same math works for gable and hip roofs, as long as every plane has the same pitch. Hip roofs have more cuts, so plan on about 15% waste instead of 10%.
Not sure of your pitch? From a ladder at the roof edge, hold a level flat out from the roof, mark 12 inches along it, and measure straight down to the roof surface. That number is the rise.
Worked example: a 40 × 30 ft house
A gable roof over a 40 × 30 ft house, with a 12-inch overhang and a 6/12 pitch, using shingles that come 3 bundles to the square.
- Add the overhang to each side
42 × 32 = 1,344 sq ft - Multiply by the 6/12 multiplier
1,344 × 1.118 = 1,503 sq ft - Convert to squares
1,503 ÷ 100 = 15.03 squares - Add 10% for a gable roof
15.03 × 1.10 = 16.53 squares - Count the bundles
16.53 × 3 = 49.6 → 50 bundles - Underlayment at 940 sq ft a roll
1,653 ÷ 940 = 1.76 → 2 rolls
Drip edge runs along both eaves (2 × 42 = 84 ft) and the four rakes (4 × 16 × 1.118 = 71.6 ft), about 156 feet in all.
Roof pitch multipliers
Pitch is the rise in inches for every 12 inches of horizontal run. Multiply the flat footprint by the factor for your pitch to get the true roof area.
| Pitch | Angle | Multiplier |
|---|---|---|
| 2/12 | 9.5° | 1.014 |
| 3/12 | 14.0° | 1.031 |
| 4/12 | 18.4° | 1.054 |
| 5/12 | 22.6° | 1.083 |
| 6/12 | 26.6° | 1.118 |
| 7/12 | 30.3° | 1.158 |
| 8/12 | 33.7° | 1.202 |
| 9/12 | 36.9° | 1.250 |
| 10/12 | 39.8° | 1.302 |
| 11/12 | 42.5° | 1.357 |
| 12/12 | 45.0° | 1.414 |
Low-slope roofs may need special underlayment or a different roofing product. Check the shingle instructions and local codes.
Underlayment and drip edge
Roll coverage depends on the product. Many synthetic underlayment rolls are sold as 10 squares (1,000 sq ft), which covers about 940 sq ft once the edges overlap. Felt rolls often cover 200–400 sq ft. Type in the coverage from the label. Drip edge goes along the eaves and, on a gable roof, up the rakes. On a hip roof every edge is an eave. It's commonly sold in 10-foot pieces, so divide the length by 10 and round up.
Questions people ask
How many bundles of shingles are in a square?
Most standard asphalt shingles come 3 bundles to the square, which covers 100 sq ft. Some heavier shingles take 4 or more, so check the wrapper.
How do I find my roof pitch?
Pitch is the rise over a 12-inch run. Hold a level flat out from the roof, mark 12 inches, and measure down to the roof. A 6-inch drop means a 6/12 pitch.
How much extra shingles should I order?
About 10% for a simple gable roof and 15% for a hip roof. Add more for roofs with lots of valleys, dormers or skylights.
Can I measure my roof from the ground?
Yes. Measure the house footprint, add the overhang on each side, and multiply by the pitch multiplier. That gives a close estimate of the roof area without climbing up.
Sources
The numbers in this calculator come from these manufacturer specs and public guides. Always check the label on the product you buy.
- A roofing square is 100 sq ft; bundles per square; slope as rise over run — Owens Corning
- Standard 3-tab shingles: 3 bundles per square — Owens Corning Supreme
- Synthetic underlayment in 10-square rolls (937 sq ft after overlap) — Owens Corning