How to calculate concrete for fence posts
Each post hole is a cylinder. Work out its volume, take away the space the post itself fills, and multiply by the number of posts. Then divide by the yield printed on the bag and round up.
Measure the diameter and depth in inches. Dividing by 1,728 turns cubic inches into cubic feet. Lumber is smaller than its name: a 4×4 is really 3.5 × 3.5 in, so it fills 12.25 sq in of the hole. A 6×6 is 5.5 × 5.5 in, or 30.25 sq in. A 50-lb bag of fast-setting mix yields about 0.375 cu ft.
Many builders put a few inches of gravel in the bottom of each hole so water can drain away from the end of the post. If you do, enter only the depth that will be filled with concrete.
Worked example: nine 4×4 fence posts
Say you're building about 64 feet of fence with posts every 8 feet. That's 9 posts, each set in a 10-inch hole that's 24 inches deep.
- Find the area of the hole
π × 5² = 78.5 sq in - Subtract the 4×4 post
78.5 − 12.25 = 66.3 sq in - Multiply by the depth, convert to cubic feet
66.3 × 24 ÷ 1,728 = 0.92 ft³ - Nine posts, plus 10% extra
0.92 × 9 × 1.10 = 9.1 ft³ - Divide by the 50-lb bag yield
9.1 ÷ 0.375 = 24.3 → 25 bags
That works out to about 2.7 bags per post. With regular 80-lb bags (0.60 cu ft each) the same job takes 16 bags.
How wide should a post hole be?
A common rule of thumb is a hole about three times as wide as the post. That leaves a solid collar of concrete on every side. Going much wider mostly adds bags, not strength.
| Post | Actual size | Typical hole diameter |
|---|---|---|
| 4×4 | 3.5 × 3.5 in (8.9 cm) | 10–12 in (25–30 cm) |
| 6×6 | 5.5 × 5.5 in (14 cm) | 16–18 in (40–45 cm) |
| Round, 4 in | 4 in (10 cm) across | 12 in (30 cm) |
How deep should fence posts go?
Many builders bury about one-third to one-half of the post's height above ground. Taller fences and windy spots sit toward the deeper end. Where the ground freezes, the bottom of the hole should also sit below the frost line.
| Height above ground | One-third rule | One-half rule |
|---|---|---|
| 4 ft (1.2 m) | 16 in (41 cm) | 24 in (61 cm) |
| 6 ft (1.8 m) | 24 in (61 cm) | 36 in (91 cm) |
| 8 ft (2.4 m) | 32 in (81 cm) | 48 in (122 cm) |
These are guidelines, not code. Frost depth, soil and wind load vary, so check local codes before you dig.
Questions people ask
How many bags of concrete do I need per fence post?
For a 4×4 post in a 10-inch hole 2 feet deep, plan on about 2.5 bags of 50-lb fast-setting mix, or about 1.5 bags of 80-lb regular mix. Wider or deeper holes need more.
How big should a fence post hole be?
A common rule of thumb is about three times the width of the post: 10–12 inches across for a 4×4 and 16–18 inches for a 6×6.
How deep should fence posts be set?
Many builders bury about one-third to one-half of the height above ground, and go below the frost line in cold areas. Check local codes for your area.
Should I use fast-setting or regular concrete?
Fast-setting mix needs no mixing, which makes it handy for a few posts. Regular mix usually costs less per post but has to be mixed before you pour it.
Sources
The numbers in this calculator come from these manufacturer specs and public guides. Always check the label on the product you buy.
- Hole 3× the post width, ⅓–½ of the above-ground height deep — Quikrete
- A 50-lb bag of fast-setting concrete yields about 0.38 cu ft — Sakrete
- Bag yields: 50 lb ≈ 0.375, 60 lb ≈ 0.45, 80 lb ≈ 0.60 cu ft — Quikrete Concrete Mix